Using ProChannel

To enable/disable a module

In the expanded ProChannel, click the module’s enable/disable button .

Note: The more ProChannel modules you enable, the more CPU resources are required from your computer.

To insert a module

Do one of the following:

Click the Insert Module button in the Inspector and choose a module on the pop-up menu.

Right-click a module header or blank space in ProChannel and select Insert Module on the pop-up menu.

Figure 285. Click the Insert Module button to insert a new module.

 

Note: You can insert multiple instances of external ProChannel modules. However, you can not insert multiple instances of the internal ProChannel modules, including QuadCurve Equalizer, Tube Saturation, PC76 U-Type compressor, and PC4K S-Type bus compressor.

To remove a module

Right-click the module header and select Remove Module on the pop-up menu.

To replace a module

Right-click a module header or blank space in ProChannel and select Replace Module on the pop-up menu.

To reorder a module

The signal flows from top to bottom. Click a module’s gripper and drag the module up/down to the desired position.

Figure 286. Drag a module’s gripper up/down to reorder the signal chain.

To select a module

Click a module to make it the active module. The active module is shaded slightly. You can use ACT to control parameters in the active module, and all context menu commands operate on the active module when right-clicking an empty space in ProChannel.

To specify the default ProChannel configuration

1.	Insert and arrange the ProChannel modules in the desired order.

2.	Do one of the following:

To specify the default configuration for tracks. Right-click any empty space in a track’s ProChannel and select Set Modules as Default for Tracks on the pop-up menu.

To specify the default configuration for tracks. Right-click any empty space in a bus’ ProChannel and select Set Modules as Default for Buses on the pop-up menu.

To route ProChannel pre-effects bin or post-effects bin

By default, the ProChannel signal is routed prior to the channel’s effects bin (pre). To route ProChannel after the effects bin (post), right-click any empty space in ProChannel and select Post-FX bin on the pop-up menu.

To interact with the QuadCurve Equalizer graph

The QuadCurve Equalizer graph is divided into four sections, which correspond to the Low, Low-Mid, Mid-High and High bands. When you move the mouse pointer over the graph, the current band is highlighted.

Note: The High Pass filter and Low Pass filter can not be edited from the graph.

To adjust a band’s gain, drag up/down.

To adjust a band’s frequency, drag left/right.

To adjust a band’s Q, hold down the ALT key and drag up/down.

To adjust parameters with finer precision, hold down the SHIFT key while dragging.

To enable/disable a band, click the band’s region in the graph.

To change the plot resolution globally, right-click any QuadCurve Equalizer graph in the Console view and choose the desired resolution on the pop-up menu. The resolutions are as follows:

Auto (graph scales dynamically)

6 dB

12 dB

18 dB

Figure 287. QuadCurve Equalizer graph.

A. Low band B. Low-Mid band C. Mid-High band D. High band

To sidechain the ProChannel compressor

1.	Add the PC4K S-Type Bus Compressor module.

2.	Under Side Chain, click the On/Off toggle.

Figure 288. Add the PC4K S-Type Bus Compressor module in order to use sidechaining.

 

See also:

Sidechaining

To use presets

Do one of the following:

To load an existing preset, click the Load Preset button and navigate to the desired preset file.

To save a new preset or overwrite the current preset, click the Save Preset button , type a name, then click Save.

Note: To see the Load Preset and Save Preset buttons in the Inspector and collapsed Console view strips, hover the mouse over the Preset control.

Figure 289. Use presets to save and recall favorite settings.

A. Current preset B. Load Preset C. Save Preset

To lock ProChannel in the Inspector pane

By default, the Track Inspector dynamically updates to show the current track. However, you can choose to always show a specific instance of ProChannel regardless of which track is current.

1.	Click the track or bus you want to show in the Track Inspector.

2.	Click the ProCh button at the top of the Inspector.

ProChannel is displayed in the Inspector pane.

3.	Click the Track Name control at the bottom of the Inspector and select Lock the current track or bus from the drop-down menu.

To unlock the track or bus, select Lock the current track or bus from the menu again.

Keyboard navigation

When ProChannel has focus, you can use the following keys to navigate around ProChannel:

Table 175. ProChannel keyboard shortcuts  

Key	Action
PAGE UP	Scroll up
PAGE DOWN	Scroll down
HOME	Go to top
END	Go to bottom

ProChannel compatibility with SONAR X2 Studio and Essential

ProChannel is only included with SONAR X2 Producer. If a project was created in Producer and loaded into Studio or Essential, the project might sound different because ProChannel is not available. However, if you resave the project in Studio or Essential, all ProChannel settings will be persisted and available if you later load the project into Producer again.

Loading legacy projects

If you load a pre-SONAR X2 project that uses the per-channel Sonitus:fx EQ, the ProChannel QuadCurve Equalizer module will be disabled.

If you want to keep and edit the Sonitus:fx EQ, double-click the small Equalizer graph in the collapsed ProChannel.

To replace the Sonitus:fx EQ with the ProChannel QuadCurve Equalizer, do one of the following:

Press CTRL and click the Equalizer enable/disable button .

Enable the Equalizer module. SONAR prompts if you want to switch from the Sonitus:fx EQ to the ProChannel QuadCurve Equalizer.

Loading X2 projects in SONAR X1c or earlier

SONAR X1c and earlier only support a single compressor module per channel. If you are using multiple compressor modules on a channel in a SONAR X2 project, SONAR X1c (or earlier) will only load one of the compressors.

SONAR X1c and earlier always shows the Compressor, Equalizer and Tube Saturation modules on all channels. If you load a SONAR X2 project that doesn’t use all the default modules, SONAR X1c will automatically recreate the missing modules.

If you load a SONAR X2 project that has ProChannel Global Bypass enabled, you will not be able to unbypass that ProChannel instance in SONAR X1c.

 

See:

ProChannel modules and controls

PC76 U-Type Channel Compressor module

PC4K S-Type Bus Compressor module

QuadCurve Equalizer module

Tube Saturation module

Console Emulator module

FX Chain module

 

See also:

Track Inspector overview

Console view

Mixing